Microstructure and mechanical properties of α/β-Si3N4 composite ceramics with novel ternary additives prepared via spark plasma sintering

In this study, α/β-Si₃N₄ composite ceramics with high hardness and toughness were fabricated by adopting two different novel ternary additives, ZrN–AlN–Al₂O₃/Y₂O₃, and spark plasma sintering at 1550 °C under 40 MPa. The phase composition, microstructure, grain distribution, crack propagation process and mechanical properties of sintered bulk were investigated. Results demonstrated that the sintered α/β-Si₃N₄ composite ceramics with ZrN–AlN–Al₂O₃ contained the most α phase, which resulted in a maximum Vickers hardness of 18.41 ± 0.31 GPa. In the α/β-Si₃N₄ composite ceramics with ZrN–AlN–Y₂O₃ additives, Zr₃AlN MAX-phase and ZrO phase were found and their formation mechanisms were explained. The fracture appearance presented coarser elongated β-Si₃N₄ grains and denser microstructure when 20 wt% TiC particles were mixed into Si₃N₄ matrix, meanwhile, exhibited maximum mean grain diameter of 0.98 ± 0.24 μm. As a result, the compact α/β-Si₃N₄ composite ceramics containing ZrN–AlN–Y₂O₃ additives and TiC particles displayed the optimal bending strength and fracture toughness of 822.63 ± 28.75 MPa and 8.53 ± 0.21 MPa?m^1/2, respectively. Moreover, the synergistic toughening of rod-like β-Si₃N₄ grains and TiC reinforced particles revealed the beneficial effect on the enhanced fracture toughness of Si₃N₄ ceramic matrix.     

Effects of non-thermal plasma treating wheat kernel on the physicochemical properties of wheat flour and the quality of fresh wet noodles

The effects of non-thermal plasma (NTP) on the physicochemical properties of wheat flour and the quality of fresh wet noodles ( FWN) were investigated. The results showed that NTP effectively decreased the total plate count (TPC), yeast and mould count (YMC) and Bacillus spp. in wheat flour. Wet gluten contents and the stability time reached the maximum when treated for 20 s. The viscosity of starch increased significantly after treatment due to the increased of damaged starch. The contents of secondary structure were altered to some extent, which was because that the ordered network structure of gluten protein broken. Furthermore, compared with the control, texture properties of FWN were enhanced significantly at 20 s, and the darkening rate of FWN was greatly inhibited due to the low polyphenol oxidase (PPO) activity. Consequently, the most suitable treatment was 500 W for 20 s, providing a basis for the application of NTP in flour products.     

Solution plasma-assisted preparation of highly dispersed NiMnAl-LDO catalyst to enhance low-temperature activity of CO2 methanation

In this work, the solution plasma-assisted method was used to prepare NiMnAl-LDO (layered double oxides) catalysts with different treatment times, which were used for the CO₂ methanation reaction. Solution plasma treatment can enhance the dispersibility of the catalyst, create oxygen defects and improve the chemical adsorption capacity of the catalyst. The results show that the low-temperature activity of the catalyst has been improved after the solution plasma treatment. We demonstrate that the NiMnAl-LDO-P(20) catalyst with high dispersion has the highest catalytic activity in CO₂ methanation (81.3% CO₂ conversion and 96.7% CH₄ selectivity at 200 °C). Even though working for 70 h, the catalyst is still highly stable. This work provides a great promise for improving the low-temperature activity of Ni-based catalysts.     

Ni-based catalysts with coke resistance enhance by radio frequency discharge plasma for CH4/CO2 reforming

Coke deposition has been considered to be one of the most important reasons hindering the stability of the catalyst during CH₄/CO₂ reforming. In this study, after the addition of P123 (PEG-PPG-PEG triblock copolymer), Ni²⁺ can be well-dispersed on the mesoporous molecular sieve MCM-41. And then, the catalysts were prepared by using N₂ radio frequency (RF) discharge plasma for different treatment times to reduce the size of Ni particles, improve the anti-coking performance, and thereby improve the stability of the catalyst. The results showed that the catalyst NM-P123-PN2h exhibits superior catalytic properties in the CH₄/CO₂ reforming. The initial conversions of CH₄ and CO₂ were 90.80% and 89.60% at 750 °C, respectively. The catalyst NM-P123-PN2h showed highly coke resistance with less carbon deposition (1.12%) at 750 °C after 10 h of continuous reaction, while the carbon deposition of the catalyst NM-C was 37.32%. Compared with the traditional calcination method, the catalyst prepared by plasma treatment has a smaller particle size and better dispersibility of nickel. In particular, the nickel particle size of the catalyst NM-C was 8.37 nm, however, that of the catalyst NM-P123-PN2h was only 1.70 nm, and the nickel particle size was reduced by 5 times. Therefore, it can be concluded that the catalyst prepared under the combined action of P123 and RF plasma-treated can effectively improve the coke resistance of the catalyst and the stability of the CH₄/CO₂ reforming.     

Recursive algorithm for modeling non-linear etching rates in reactive plasma jet based optical surface machining of borosilicate crown glass

Application-specific optical glass properties are achieved by utilizing complex material compositions. This can be problematic in reactive plasma-assisted deterministic surface processing since a non-volatile surface layer may form depending on the glass composition, which affects the etch rate and thereby the local etching depth. In this investigation, a model algorithm is proposed to tackle some restrictions in applying fluorine-based plasma jet as etching tool utilized for freeform surface machining of optics made of complex glass composition, like borosilicate crown glass (e.g., N-BK7®). In this regard, firstly an analytical model is proposed for estimating the depth-dependent etch rate function. Subsequently, a recursive simulation algorithm is introduced for convolving the derived depth-dependent etch rate function with the given dwell time matrix to simulate a deterministic freeform generation process. By the proposed simulation algorithm, the impeding influence of the residual layer on the reduction of etching depth is computed prior to a real experiment in order to scale the local dwell time to ensure the targeted local removal. Finally, the simulated freeform shape is compared with the corresponding result of an etching experiment to validate the feasibility of the proposed approach.     

Unipolar plasma electrolytic oxidation: Waveform optimisation for corrosion resistance of commercially pure titanium

This study deals with the anodisation of titanium grade 2 in 0.5-M sulphuric acid using a pulsed signal in a unipolar regime. The electrical parameters investigated are voltage, frequency and duty cycle. The use of duty cycles with a high percentage of anodic polarisation (90%), combined with high frequencies (1000 Hz) and the higher voltage tested (220 V), favoured the establishment of a plasma regime involving strong dielectric discharges, allowing the growth of thicker oxides but with rough architecture. The corrosion resistance of the formed film has been characterised by potentiodynamic tests in 0.5-M NaBr for localised corrosion resistance and by immersion tests in 10% v/v sulphuric acid solution for a uniform corrosion assessment. Current–time curves, visual observations and electron microscope analysis (scanning electron microscopy, energy-dispersive X-ray spectroscopy) were the tools selected to provide a correlation between technological parameters and oxide growth mechanism. For localised and uniform corrosion, anodisation at 220 V with a high level of anodic polarisation (90%) and frequency (1000 Hz) was verified to be particularly advantageous.     

Systematic Review: Adipose-Derived Mesenchymal Stem Cells,Platelet-Rich Plasma and Biomaterials as New Regenerative Strategies in Chronic Skin Wounds and Soft Tissue Defects

The number of clinical trials evaluating adipose-derived mesenchymal stem cells (AD-MSCs), platelet-rich plasma (PRP), and biomaterials efficacy in regenerative plastic surgery has exponentially increased during the last ten years. AD-MSCs are easily accessible from various fat depots and show intrinsic plasticity in giving rise to cell types involved in wound healing and angiogenesis. AD-MSCs have been used in the treatment of soft tissue defects and chronic wounds, employed in conjunction with a fat grafting technique or with dermal substitute scaffolds and platelet-rich plasma. In this systematic review, an overview of the current knowledge on this topic has been provided, based on existing studies and the authors’ experience. A multistep search of the PubMed, MEDLINE, Embase, PreMEDLINE, Ebase, CINAHL, PsycINFO, Clinicaltrials.gov, Scopus database, and Cochrane databases has been performed to identify papers on AD-MSCs, PRP, and biomaterials used in soft tissue defects and chronic wounds. Of the 2136 articles initially identified, 422 articles focusing on regenerative strategies in wound healing were selected and, consequently, only 278 articles apparently related to AD-MSC, PRP, and biomaterials were initially assessed for eligibility. Of these, 85 articles were excluded as pre-clinical, experimental, and in vitro studies. For the above-mentioned reasons, 193 articles were selected; of this amount, 121 letters, expert opinions, commentary, and editorials were removed. The remaining 72 articles, strictly regarding the use of AD-MSCs, PRP, and biomaterials in chronic skin wounds and soft tissue defects, were analyzed. The studies included had to match predetermined criteria according to the patients, intervention, comparator, outcomes, and study design (PICOS) approach. The information analyzed highlights the safety and efficacy of AD-MSCs, PRP, and biomaterials on soft tissue defects and chronic wounds, without major side effects.     

Efficient hydrogen evolution by liquid phase plasma irradiation over Sn doped ZnO/CNTs photocatalyst

In this study, the liquid phase plasma (LPP) was irradiated over pure zinc oxide (ZnO), strontium (Sn) doped ZnO, and Sn doped ZnO/CNTs photocatalysts for hydrogen evolution from pure water and from aqueous solution of water-methanol. The possible relationship between hydrogen evolution and optical emissions from LPP for activation of ZnO based photocatalysts was revealed. The role of carbon nanotubes (CNTs) as a support material for improved photocatalytic hydrogen evolution was also investigated in this study. The photocatalytic hydrogen evolution from water mixed methanol under LPP irradiation was compared with pure water splitting. The photolysis produced negligible amount of hydrogen due to minimal photodecomposition of water molecules under LPP irradiation. The plasma born reactive species also played crucial role in photolysis. However, the hydrogen evolution rate increased significantly in the presence of ZnO photocatalyst. Further improvement in hydrogen evolution rate was noticed on Sn doping of ZnO and compositing with CNTs. The highest hydrogen evolution rate of 11.46 mmh⁻¹g⁻¹ from water mixed methanol was achieved with Sn doped ZnO/CNTs photocatalyst. This hydrogen evolution rate from water-methanol solution was 9 times higher than from the splitting of pure water. This hydrogen evolution rate is attributed to excessive production of hydroxyl radicals, red shift in optical band gap of Sn doped ZnO/CNTs photocatalyst, slow electron-hole recombination and fast decomposition of methanol as sacrificial reagent.     

Large electrocaloric effect in two-step-SPS processed Pb(Sc0.25In0.25Nb0.25Ta0.25)O3 medium-entropy ceramics

Ferroelectric ceramic with a large electrocaloric (EC) effect at a very low electric field is very attractive in the next solid state refrigeration technology. In this work, two Pb(Sc_0.25In_0.25Nb_0.25Ta_0.25)O₃ (PSINT) medium-entropy ceramics were successfully synthesized by a spark plasma sintering (SPS) technology, including one-step-SPS processed and two-step-SPS processed samples. A large EC effect (△T ～ 0.85 K) with a high EC strength (△T/△E ～ 0.021 K cm/kV) around room temperature are obtained at a very low electric field (～40 kV/cm) in the two-step-SPS processed sample. Moreover, the working temperature range is very broad (～120 K), which can be responsible for the high relaxation degree of the dielectric peak. It can be believed that the PSINT medium-entropy ceramics can be promising candidates for application in the next-generation EC cooling devices.     

Synthesis of cubic and monoclinic hafnia nanoparticles by pulsed plasma in liquid method

Hafnia (HfO₂, hafnium dioxide) is a wide band gap and high-κ material, and the metastable cubic hafnia has a much higher permittivity compared with the normal monoclinic hafnia. Here, we employ a one-step process, the pulsed plasma in liquid (PPL) method to synthesize two types of hafnia nanoparticles (NPs): one which is mainly in cubic phase (cubic: 81.7 at%, monoclinic: 18.3 at%) and the other which is in monoclinic phase. High-resolution transmission electron microscopy images showed that the particles were small (particle size ~3 nm). X-ray absorption fine structure analysis showed no chemical shifts, indicating that the synthetic hafnia NPs contained no oxygen vacancy. The synthetic hafnia NPs mainly in cubic phase showed a much higher relative permittivity than that of the commercial hafnia (monoclinic), and have a larger band gap than the synthetic monoclinic hafnia NPs.